← All articles

A guard removed “just for a setup”. A safety switch held down with tape. An emergency stop hidden behind a pallet. On the floor, these situations seem routine. For a CNESST inspector, they stand out right away. Here are the points to check before their visit.

Key takeaways

  • Quebec’s RSST requires a machine to make its danger zones inaccessible. If not, protective measures must reduce the risk (section 177).
  • A guard that is removed, bypassed or disabled is easy for an inspector to spot.
  • Workers must know why the guard is there and what to do during a setup. That’s a training issue.

In this article

  1. What the RSST says, in plain words
  2. The 6 points to check before the visit
  3. Why guards disappear
  4. Walk your machines in 5 steps
  5. Training, the forgotten link

What the RSST says, in plain words

Quebec’s Regulation respecting occupational health and safety (RSST) has a full section on machines. Here are the main rules:

S. 177

Danger zones inaccessible

The machine must prevent access to danger zones. If not, at least one protective measure must reduce the risk.

S. 180

Kept in good condition

The machine and its protective measures must stay in good condition, as per the manufacturer’s manual.

S. 186

No removal

A protective measure can’t be removed, except in the cases set out in the regulation.

S. 188

Setup and maintenance

If a guard must be moved for a setup, a specific control mode must protect the worker.

S. 191

Deliberate start

The machine must start only through a deliberate action on a control designed for that purpose.

S. 176

Modifications

A modification that may affect safety must be done under an engineer’s supervision.

The regulation also requires every machine to come with the manufacturer’s instruction manual (section 174). And lockout has its own rules, which we explain in our article on 7 lockout mistakes. The CNESST also explains these requirements on its page Exposure to the hazardous areas of a machine.

The 6 points to check before the visit

Walk your floor with these six questions in mind:

1

Is a guard missing or poorly fastened?

A guard removed for a setup and never put back. Or a guard held by a single screw.

2

Is a safety device bypassed?

A switch held down with tape, a magnet or a wire. This is serious: the machine looks protected, but no longer is.

3

Is the emergency stop accessible and working?

Nothing should block it. Test it regularly.

4

Was a machine modified in-house?

An add-on, a higher speed, a replaced part, with no safety analysis.

5

Are clothing and accessories safe?

Near moving parts: no loose clothing or jewellery, and long hair tied back (section 179).

6

Can the worker explain the guards?

Ask them why this guard is there and what to do for a setup. If they hesitate, training is missing.

Why guards disappear

A guard never disappears without a reason. You need to understand why, or it will disappear again:

  • It slows production. The operator is paid or measured on output.
  • It gets in the way of frequent setups. Removing it becomes a habit.
  • It’s poorly designed. It blocks the view or access to a part.
  • Nobody is responsible for checking it. Its absence goes unnoticed.

The solution isn’t just to put it back. You need to fix the cause: improve the guard, plan a safe setup method and train operators.

Walk your machines in 5 steps

1

Take inventory

List your machines and their protective measures: guards, interlocks, light curtains, emergency stops.

2

Check every protection

Is the guard in place? Does the interlock really stop the machine when the door opens?

3

Look for bypasses

Tape, magnets, wires, guards left permanently open. Check the evening and night shifts too.

4

Talk to operators

Ask them what bothers them. They know why the bypasses exist.

5

Fix, document and train

Repair, record the correction and train operators. Keep proof of every step.

A guard that gets in the way will be removed. A guard that’s understood will be respected.

Quebec’s Act respecting occupational health and safety (section 51) requires employers to give workers appropriate training, coaching and supervision. For machines, that means every operator must know:

  • what each protection on their machine is for;
  • how to do a setup or clear a jam safely;
  • when lockout is required;
  • what to do if they find a damaged protection.

A visual work instruction at the workstation recalls the right method. A skills matrix shows who is trained on which machine. And a training record keeps the proof, ready for the inspector.

Frequently asked questions

Can a guard be removed to do a setup?

Only in the cases set out in the regulation. You must then use a specific control mode that protects the worker, or lock out the machine. The guard must be back in place before normal operation resumes.

Who is responsible for machine guarding?

The employer must make sure machines are safe and workers are trained. Workers, for their part, must follow safety rules and not bypass protections.

Do old machines have to meet these rules?

Yes. The RSST rules cover any machine in service in an establishment, whatever its age.

What can an inspector do if they find a hazard?

They can issue a correction notice. If the danger is serious, they can also order the machine stopped until the situation is corrected.

Want your operators to truly understand the protections on their machines? Witeach builds training filmed on your equipment, with training records ready for the inspector.

Free succession plan →Talk to an expertExplore the platform

Share this article

What if we preserved your experts’ knowledge?

Every retirement takes years of experience with it. Let us talk about how to capture and pass on that knowledge before it leaves.

Let us discuss your needs