← All articles

In almost every plant, there’s a binder full of ten-page procedures. They were carefully written, approved, filed… and nobody reads them. On the floor, operators do what a coworker showed them. A one-page visual work instruction, posted at the workstation, changes that.

Key takeaways

  • A procedure nobody reads protects neither quality nor safety: a one-page visual sheet at the workstation actually gets used.
  • A good sheet means photos of your workstation, five to eight numbered steps and colour-coded key points for safety and quality.
  • It is built with your best operator, tested with a new employee and updated with every change.

In this article

  1. Why long procedures aren’t followed
  2. Procedure, work instruction, training: three different tools
  3. What a good sheet looks like
  4. Turning a procedure into a sheet, step by step
  5. Writing rules that make the difference
  6. Keeping sheets up to date

Why long procedures aren’t followed

The problem isn’t operators’ attitude. It’s the format:

  • They’re far from the job: in an office or a binder, while the task happens at the machine.
  • They’re too long: useful information is buried in paragraphs, definitions and references.
  • They’re written for the auditor, not the operator: the vocabulary is administrative, not the shop floor’s.
  • They’re often outdated: the machine was modified, but the document wasn’t.

Procedure, work instruction, training: three different tools

These three tools often get mixed up. Yet each has its own role:

📘

The procedure

Describes the what, who and why of a process. It serves as a reference and meets audit requirements.

It stays in the office or the quality system.

🗂️

The work instruction

Shows how to do one specific task, step by step, with images.

It is posted at the workstation, where the work happens.

🎓

Training

Lets people learn the task, practise it and prove they’ve mastered it.

It relies on the work instruction; it doesn’t replace it.

So the ten-page procedure isn’t useless: it simply isn’t the right tool for the floor. The visual work instruction is its operational version.

What a good sheet looks like

Here’s the structure of an effective visual work instruction. Each step has its photo, a clear action and, when needed, a key point:

WI-042 · Tool change, press 3Rev. 3 · Approved by: supervisor · 2026-10-13
🔒1

Lock out the press

⚠ Verify zero energy before touching

🔧2

Loosen the 4 clamps

💡 Cross pattern: 1-3-2-4

⬆️3

Remove the tool with the hoist

⚠ Never by hand: over 25 kg

📏4

Install and align the new tool

★ 0.5 mm gap checked with a gauge

✅5

First piece: inspection

★ Compare to the template before running

⚠ Safety  ·  ★ Quality  ·  💡 Trick of the trade

Fictional example. In a real sheet, each box contains a photo of your workstation.

Notice what isn’t there: no paragraphs, no definitions, no regulatory references. All of that stays in the procedure. The sheet keeps only what the operator needs, when they need it.

Turning a procedure into a sheet, step by step

1

Pick the right task

Start with a task that causes errors, stoppages or injuries, or that new hires find difficult.

2

Watch your best operator

Watch them do the task, film it on a phone and ask why they make each move. That’s where the real know-how hides.

3

Break it into 5 to 8 main steps

A step is an action that moves the work forward. If you have more than eight, split the task into two sheets.

4

Identify the key points

For each step: is there a safety risk, a critical quality point or a trick of the trade that makes the job easier?

5

Photograph each step

On your real machine, from the right angle, with arrows or circles on the important detail.

6

Test it with a new employee

Ask someone who doesn’t know the task to do it using only the sheet. Every hesitation shows a step to clarify.

7

Post it and control the version

Laminate the sheet, post it at the workstation and show the revision number, the date and who approved it.

The second step matters most. To learn more about drawing out your experts’ knowledge, see our article on documenting procedures from operator know-how.

Writing rules that make the difference

✅ Do

  • Start every step with an action verb
  • One action per step
  • Use shop-floor words, always the same ones
  • Put safety in red, quality in blue
  • Keep the sheet to a single page

❌ Avoid

  • Paragraphs and long sentences
  • Generic images or blurry drawings
  • Abbreviations only veterans understand
  • Cascading “if… then… unless…”
  • A sheet with no date or revision number

A well-written sheet helps everyone, especially employees who are learning French. See our tips for training immigrant workers in manufacturing.

Keeping sheets up to date

An outdated sheet is more dangerous than no sheet at all, because people trust it. A few simple rules:

  • Every change to a machine, tool or method triggers a revision of the sheet.
  • The old version is removed from the workstation the same day the new one is posted.
  • All sheets are reviewed at least once a year with the operators.
  • Every sheet carries a number, a date and the name of the person who approved it.

This discipline also meets ISO 9001 requirements for the control of documented information (clause 7.5). And for high-risk tasks such as lockout, a clear sheet at the workstation is a natural complement to the procedure required by regulation.

The best procedure isn’t the most complete one. It’s the one operators actually follow.

One last idea: add a QR code to the sheet that leads to a short video module of the task. The sheet recalls the steps; the video shows the movement.

Frequently asked questions

What’s the difference between a procedure and a work instruction?

A procedure describes a full process: the what, who and why. A work instruction shows how to do one specific task, step by step, and is posted at the workstation.

How many steps should a sheet contain?

Ideally five to eight. Beyond that, the sheet becomes hard to follow; it’s better to split the task into two sheets.

Who should write work instructions?

Your most experienced operator, supported by a supervisor or trainer who structures the information. Final approval belongs to the area manager.

Does a visual sheet replace training?

No. The sheet is a reminder at the workstation. Employees must first be trained and show they’ve mastered the task, and that training must be documented.

Are your procedures gathering dust in a binder? Witeach draws out your best operators’ know-how on the floor and turns it into visual instructions and training your employees actually follow.

Free succession plan →Talk to an expertExplore the platform

Share this article

What if we preserved your experts’ knowledge?

Every retirement takes years of experience with it. Let us talk about how to capture and pass on that knowledge before it leaves.

Let us discuss your needs